Skip to content
SLEIGHT
← The Library

How to Open a Pocket Watch Back (Snap, Screw or Hinged) and Change the Battery

Nov 15, 2026 · The Editors

How to open a pocket watch: the front cover, the back case, snap-back, screw-back and hinged backs, the inner dust cover, and how to change a quartz pocket watch battery safely.

To open a pocket watch, press the crown to release the front cover; to open the back, find out whether it snaps, screws or hinges, then use a fingernail or case knife at the lip (snap or hinge) or turn it anticlockwise (screw). Never force it: a watch that will not open is usually the other kind.

How to open the front of a pocket watch

Hunter case watches have a cover over the dial. Press the crown down firmly with your thumb and the cover springs open. If yours does not have a crown button, look for a small catch at the edge. Open-face watches have no front cover; you see the time through the crystal. See hunter vs open face pocket watch.

The three kinds of pocket watch back

BackHow to recognise itHow to open
Hingeda small hinge visible at one side, a lip or nail notch oppositefingernail in the notch, lift
Snap-backa smooth edge with a small lip or notch, no hinge, no ridgescase knife in the notch, twist gently
Screw-backfine ridges or flats around the edgegrip and turn anticlockwise

Opening a hinged back

Look opposite the hinge for a small lip. Slide a fingernail under it and lift. Many antique watches have two covers at the back: the outer case, and an inner dust cover (sometimes engraved by the maker or a past repairer). The dust cover is opened the same way.

Opening a snap-back

  1. Find the notch or lip on the edge of the back.
  2. Hold the watch face-down on a soft cloth.
  3. Insert a watch case knife (a blunt, wedge-shaped blade made for the job) into the notch.
  4. Twist the blade gently rather than prying, until the back pops.
  5. To close, line it up and press firmly with your palms — or use a case press for a tight back.

Avoid kitchen knives and screwdrivers: they slip, scratch the case and cut fingers.

Opening a screw-back

Hold the watch firmly and turn the back anticlockwise. A rubber jar-opener pad or a rubber ball pressed onto the back gives grip. If it will not move, stop — a stuck screw-back is a job for a watchmaker's case wrench.

How to change a pocket watch battery

Only quartz pocket watches use a battery. A mechanical watch has a spring and needs winding instead; see how to wind a pocket watch.

  1. Open the back as above, on a clean, soft surface.
  2. Note the battery number printed on the old cell before removing it. Many watch batteries are small silver-oxide button cells, and the number tells you the exact replacement.
  3. Lift the battery out with a plastic or wooden toothpick. Some are held by a small clip; ease the clip aside, do not bend it.
  4. Fit the new battery the same way up as the old one (usually the flat, marked side up).
  5. Check the second hand moves, then close the back.
  6. Set the time — see how to set a pocket watch.

Handle the new battery by its edges; skin oil on the faces can shorten its life. Recycle the old one rather than putting it in household waste, and keep button batteries away from anyone who might swallow them.

When to take it to a watchmaker instead

  • the back will not move with gentle pressure;
  • the watch is an antique, valuable or sentimental;
  • there is moisture, rust or corrosion inside;
  • a new battery does not start it.

Frequently asked questions

How do you open the back of a pocket watch?

Check whether it is hinged, snap-back or screw-back. Lift a hinged or snap back at its notch with a fingernail or case knife; turn a screw-back anticlockwise.

How do you open a pocket watch to see the time?

On a hunter case watch, press the crown down firmly and the front cover springs open. Open-face watches show the time without opening.

How do you change the battery in a pocket watch?

Open the back, note the number printed on the old cell, lift it out with a plastic tool, fit the same type the same way up, then close the back and reset the time.

What tool do you need to open a pocket watch?

For a snap-back, a watch case knife; for a screw-back, a grip pad or a case wrench. Hinged backs usually open with a fingernail.