Skip to content
SLEIGHT
← The Library

How to Lube a Speed Cube (3×3), With or Without Taking It Apart

Nov 16, 2026 · The Editors

How to lube a speed cube: which lube goes where, how to do it without taking the cube apart, how often to do it, and why household oils and sprays are a bad idea.

To lube a speed cube, turn one face 45 degrees, put one or two drops of silicone cube lube into the gap onto the inner pieces, turn the cube to spread it, and repeat on the other faces. Use a little, wipe off any excess, and give it time to settle. You do not need to take the cube apart.

Why lube a speed cube

Lube makes turning smoother, quieter and more consistent. A dry cube feels scratchy and catches; a well-lubed one glides. Most new speed cubes come lubed from the factory, so a brand-new cube rarely needs any. Lube comes in once it starts to feel dry, gritty or loud after weeks of use.

Which lube to use

Cube lubes are made from silicone, which does not harm the plastic. They come in two broad kinds:

LubeWhere it goesWhat it does
Thin, fast lubebetween the piecesspeeds turning, lighter feel
Thick, slow lubecore and springssmoother, quieter, more control

For a first try, a single bottle of general-purpose silicone cube lube is enough.

Lubing a cube with household items

There is no good household substitute. Cooking oil goes sticky, petroleum jelly gums up, and spray lubricants such as WD-40 can weaken or crack many plastics. If you have no cube lube, it is better to clean the cube and leave it dry than to use those.

How to lube a 3×3 speed cube without taking it apart

  1. Clean first. Wipe the cube and turn it a few dozen times to shake out dust.
  2. Turn the top face 45 degrees. This opens a gap that shows the inner pieces.
  3. Add one or two drops into the gap, onto the pieces of the middle layer, not the outside.
  4. Turn the top face back and forth a few times to spread it.
  5. Repeat for the other faces. Some cubers lube only two or three faces and let turning spread it.
  6. Turn the whole cube for a minute, then wipe off any lube on the outside.
  7. Let it settle. Many cubers leave it a few hours before judging the feel.

With a magnetic cube, the method is the same; the magnets sit inside the pieces and are not affected by lube.

How to lube the core

The core and springs take thick lube. To reach them you remove a centre cap and sometimes a piece; on many cubes the centre cap pops off with a fingernail. Add a small drop of thick lube to the spring and screw, then replace the cap. Only do this if you are comfortable taking pieces out, and keep the parts together.

How often to lube a speed cube

There is no fixed schedule. Lube when the cube feels dry, scratchy or noticeably slower than usual. A cube used for an hour a day might need it every few weeks; one used occasionally may go months. Too much lube is the more common mistake: it makes a cube slow and sticky, and the fix is to wipe it and wait.

Speed cubes worth lubing

A magnetic speed cube has magnets that snap each layer into line, so a light lube makes it turn smoothly and settle in the right place. If you are just starting, our 3×3 beginner's method and cube notation guide come first; what is speedcubing explains where it leads. For a puzzle that needs no lube at all, try a wooden burr cube.

Frequently asked questions

Do you need to lube a new speed cube?

Usually not. Most speed cubes come lubed from the factory. Use it for a while first, and lube only when it starts to feel dry or scratchy.

How many drops of lube does a speed cube need?

Very few: one or two drops per face, or for only a few faces. Too much makes the cube slow and sticky.

Can I use WD-40 on a speed cube?

No. Spray lubricants and oils can damage or gum up the plastic. Use a silicone lube made for cubes.

How often should you lube a speed cube?

When it feels dry, scratchy or slow. For a daily cuber that might be every few weeks; for an occasional solver, every few months.